I'm in the dog house...
-
glennPattonWork wrote:
Why ME!
goes with the territory VB boy!
speramus in juniperus
-
Rejected because of a 2mm error on the case that they were shipped in? On further thought... When you say 'case', I'm thinking shipping container. Perhaps I'm wrong?
No these are 'Hammond' 1455L cases (nice looking metal box). I milled the DVI & Power Jack 2mm to the right.
-
No these are 'Hammond' 1455L cases (nice looking metal box). I milled the DVI & Power Jack 2mm to the right.
Ahhh... Understood. :thumbsup:
-
I have dropped a DIRTY great hairy bollard, I had to case up some graphics boards to go to a customer. The cases required some milling to be done (we have a CNC milling machine) I appear to milled some of the case fronts wrong (by around 2mm) I checked the milled with a scrap board and a spare case to ensure I didn't do this wrong, due to the board being updated & sloppy tolerances in the board I now have a shipment of boards rejected by the customer. replacement panels are not available in the UK for at least until the first week of Feb at the earliest.:~ Why ME! Also anybody in CP land know anything about CamBam, Besides its porno sounding name it strikes me as the oddest interface going!
You sir, are the new poster boy for the new "Don't be like Glenn!" workplace improvement campaign. :D
It was broke, so I fixed it.
-
I have dropped a DIRTY great hairy bollard, I had to case up some graphics boards to go to a customer. The cases required some milling to be done (we have a CNC milling machine) I appear to milled some of the case fronts wrong (by around 2mm) I checked the milled with a scrap board and a spare case to ensure I didn't do this wrong, due to the board being updated & sloppy tolerances in the board I now have a shipment of boards rejected by the customer. replacement panels are not available in the UK for at least until the first week of Feb at the earliest.:~ Why ME! Also anybody in CP land know anything about CamBam, Besides its porno sounding name it strikes me as the oddest interface going!
I hope you made the Dog House to a higher standard than you made the graphics boards.
--------------------------------- Obscurum per obscurius. Ad astra per alas porci. Quidquid latine dictum sit, altum videtur.
-
I have dropped a DIRTY great hairy bollard, I had to case up some graphics boards to go to a customer. The cases required some milling to be done (we have a CNC milling machine) I appear to milled some of the case fronts wrong (by around 2mm) I checked the milled with a scrap board and a spare case to ensure I didn't do this wrong, due to the board being updated & sloppy tolerances in the board I now have a shipment of boards rejected by the customer. replacement panels are not available in the UK for at least until the first week of Feb at the earliest.:~ Why ME! Also anybody in CP land know anything about CamBam, Besides its porno sounding name it strikes me as the oddest interface going!
glennPattonWork wrote:
Also anybody in CP land know anything about CamBam
Two versions - Sam* is okay but Dave* is X|
speramus in juniperus
-
I have dropped a DIRTY great hairy bollard, I had to case up some graphics boards to go to a customer. The cases required some milling to be done (we have a CNC milling machine) I appear to milled some of the case fronts wrong (by around 2mm) I checked the milled with a scrap board and a spare case to ensure I didn't do this wrong, due to the board being updated & sloppy tolerances in the board I now have a shipment of boards rejected by the customer. replacement panels are not available in the UK for at least until the first week of Feb at the earliest.:~ Why ME! Also anybody in CP land know anything about CamBam, Besides its porno sounding name it strikes me as the oddest interface going!
-
I hope you made the Dog House to a higher standard than you made the graphics boards.
--------------------------------- Obscurum per obscurius. Ad astra per alas porci. Quidquid latine dictum sit, altum videtur.
No, no the problem isn't the graphics boards, there fine the boxes however...
-
We are not starting that again!
Oh Yes We Are! :laugh:
Never underestimate the power of stupid things in large numbers --- Serious Sam
-
I have dropped a DIRTY great hairy bollard, I had to case up some graphics boards to go to a customer. The cases required some milling to be done (we have a CNC milling machine) I appear to milled some of the case fronts wrong (by around 2mm) I checked the milled with a scrap board and a spare case to ensure I didn't do this wrong, due to the board being updated & sloppy tolerances in the board I now have a shipment of boards rejected by the customer. replacement panels are not available in the UK for at least until the first week of Feb at the earliest.:~ Why ME! Also anybody in CP land know anything about CamBam, Besides its porno sounding name it strikes me as the oddest interface going!
Measure twice, Cut once. Read the instructions again, Swear copiously.
Never underestimate the power of stupid things in large numbers --- Serious Sam
-
Measure twice, Cut once. Read the instructions again, Swear copiously.
Never underestimate the power of stupid things in large numbers --- Serious Sam
-
I have dropped a DIRTY great hairy bollard, I had to case up some graphics boards to go to a customer. The cases required some milling to be done (we have a CNC milling machine) I appear to milled some of the case fronts wrong (by around 2mm) I checked the milled with a scrap board and a spare case to ensure I didn't do this wrong, due to the board being updated & sloppy tolerances in the board I now have a shipment of boards rejected by the customer. replacement panels are not available in the UK for at least until the first week of Feb at the earliest.:~ Why ME! Also anybody in CP land know anything about CamBam, Besides its porno sounding name it strikes me as the oddest interface going!
This is exactly what they make full size decals with cut-outs for. :) Just re-mill, then place said sticker over the port covering the mistake :-D I have a mini-cnc with Mach3 on the desk next to me but I haven't gotten it fully up and going yet. I know of CamBam but haven't actually played with it.
-
Worst thing is I did!
I was building prototypes for a show in Germany - three of them, using all three populated PCBs in existence at the time, using £1000 per unit print heads, and because the metalwork was wrong they were a real pain to assemble: hundred of little washers needed to space things out, balanced carefully until you had the cover on and could get the screws in: it took ages. Couple of hours per unit instead of the 10 or 15 minutes it should have taken for production units. Running to a tight headline, because the MD was taking them with him when he drove over that night (and I'd managed to avoid going at all for the first time because I was too knackered after four months of very, very hard work to get this design up and running from scratch). Plugged in, purged and tested the first unit. It was fine. Plugged in the second unit, power on *BANG*. Oh sh*t. Dismantle it quick, knowing damn well it's fatal because of the analog smell. I'd plugged the mains onto the PSU one pin out and stuffed 240AC up it's earth...completely fried everything. Dismantle the third and check - it's fine. Reassemble (more hours) test and approve. Then have to go and confess... :-O Then on phone to hardware designers and change mains connector on all units (including current designs) to make sure it can't ever be done again. :sigh:
Never underestimate the power of stupid things in large numbers --- Serious Sam
-
I was building prototypes for a show in Germany - three of them, using all three populated PCBs in existence at the time, using £1000 per unit print heads, and because the metalwork was wrong they were a real pain to assemble: hundred of little washers needed to space things out, balanced carefully until you had the cover on and could get the screws in: it took ages. Couple of hours per unit instead of the 10 or 15 minutes it should have taken for production units. Running to a tight headline, because the MD was taking them with him when he drove over that night (and I'd managed to avoid going at all for the first time because I was too knackered after four months of very, very hard work to get this design up and running from scratch). Plugged in, purged and tested the first unit. It was fine. Plugged in the second unit, power on *BANG*. Oh sh*t. Dismantle it quick, knowing damn well it's fatal because of the analog smell. I'd plugged the mains onto the PSU one pin out and stuffed 240AC up it's earth...completely fried everything. Dismantle the third and check - it's fine. Reassemble (more hours) test and approve. Then have to go and confess... :-O Then on phone to hardware designers and change mains connector on all units (including current designs) to make sure it can't ever be done again. :sigh:
Never underestimate the power of stupid things in large numbers --- Serious Sam
Just got the latest greatest effect of the "Glenn Effect" setting up to some battery calculations for another client who is (US based) the test rig he brought over (with the VB abortion that has been the bane of my life since) was working fine had to unplug every thing and shift it as the there was another use for the meeting room. Shift that, plug everything in and poof! Tis not a good a day to be me :sigh:
-
This is exactly what they make full size decals with cut-outs for. :) Just re-mill, then place said sticker over the port covering the mistake :-D I have a mini-cnc with Mach3 on the desk next to me but I haven't gotten it fully up and going yet. I know of CamBam but haven't actually played with it.
My experience of CamBam is RUN, RUN FAST & Hide! :)
-
Just got the latest greatest effect of the "Glenn Effect" setting up to some battery calculations for another client who is (US based) the test rig he brought over (with the VB abortion that has been the bane of my life since) was working fine had to unplug every thing and shift it as the there was another use for the meeting room. Shift that, plug everything in and poof! Tis not a good a day to be me :sigh:
It's five to crackjack on Poets day: go to the pub, you can't do anything useful today!
Never underestimate the power of stupid things in large numbers --- Serious Sam
-
It's five to crackjack on Poets day: go to the pub, you can't do anything useful today!
Never underestimate the power of stupid things in large numbers --- Serious Sam
After today I'm wondering what I can break in the Pub!...
-
After today I'm wondering what I can break in the Pub!...
As long as it's not the beer pump, you'll be fine. Just stay well away from the pool table: they aren't cheap... :laugh:
Never underestimate the power of stupid things in large numbers --- Serious Sam
-
I hope you made the Dog House to a higher standard than you made the graphics boards.
--------------------------------- Obscurum per obscurius. Ad astra per alas porci. Quidquid latine dictum sit, altum videtur.
Could you have a look at this QA question: to place picture into cell's background. not whole sheet[^] It's not something I think you can do at all, but you are more likely to know than I am...
Those who fail to learn history are doomed to repeat it. --- George Santayana (December 16, 1863 – September 26, 1952) Those who fail to clear history are doomed to explain it. --- OriginalGriff (February 24, 1959 – ∞)
