Anybody know anything about potentiometers? [modified]
-
what Griff said, plus this: 1. I doubt it would be a logarithmic one. 2. I would expect a smaller value than 100K, although that is what the stamps suggest. 3. Every software person needs a multimeter; go get one right away! They come in a range of quality, functionality and price. 4. If you have a low-voltage source (say 10V), a 10K resistor and an LED, you can lit it faintly (it would take 10mA to lit properly); if you connect a second 10K in parallel, it should be twice as bright. So try the outer poles of the potentiometer as your second resistor to check it is well above 10Kohm or not. Warning: if you short-circuit the resistor, you'll blow the LED. 5. you could order a few (100K lin, 10K lin, 100K log, 10K log), postage will probably exceed material cost anyway. 6. you could call a friend with more hardware skills and buy him some :beer: :beer: :beer: :beer: :beer: :)
Luc Pattyn [Forum Guidelines] [Why QA sucks] [My Articles] Nil Volentibus Arduum
Please use <PRE> tags for code snippets, they preserve indentation, and improve readability.
Luc Pattyn wrote:
you could call a friend with more hardware skills and buy him some Beer Beer Beer Beer Beer
Best not to buy them until he has finished the job though!
------------------------------------ I will never again mention that I was the poster of the One Millionth Lounge Post, nor that it was complete drivel. Dalek Dave CCC League Table Link CCC Link[^]
-
what Griff said, plus this: 1. I doubt it would be a logarithmic one. 2. I would expect a smaller value than 100K, although that is what the stamps suggest. 3. Every software person needs a multimeter; go get one right away! They come in a range of quality, functionality and price. 4. If you have a low-voltage source (say 10V), a 10K resistor and an LED, you can lit it faintly (it would take 10mA to lit properly); if you connect a second 10K in parallel, it should be twice as bright. So try the outer poles of the potentiometer as your second resistor to check it is well above 10Kohm or not. Warning: if you short-circuit the resistor, you'll blow the LED. 5. you could order a few (100K lin, 10K lin, 100K log, 10K log), postage will probably exceed material cost anyway. 6. you could call a friend with more hardware skills and buy him some :beer: :beer: :beer: :beer: :beer: :)
Luc Pattyn [Forum Guidelines] [Why QA sucks] [My Articles] Nil Volentibus Arduum
Please use <PRE> tags for code snippets, they preserve indentation, and improve readability.
I live near an actual store so I may as well just go in and buy a few different ones. And maybe a multimeter while I'm there. It's been about 6 years since I needed to use one, it would have made figuring this out easier though. Unfortunately I don't have any hardware typey friends so I suppose I'll do what I usually do with these types of things, which is to stumble blindly through the dark and eventually find a solution (usually by luck) then give myself a pat on the back and a :beer: for being so darned clever. ;P
My current favourite phrase: Iv'e seen better!
-SK Genius
-
I live near an actual store so I may as well just go in and buy a few different ones. And maybe a multimeter while I'm there. It's been about 6 years since I needed to use one, it would have made figuring this out easier though. Unfortunately I don't have any hardware typey friends so I suppose I'll do what I usually do with these types of things, which is to stumble blindly through the dark and eventually find a solution (usually by luck) then give myself a pat on the back and a :beer: for being so darned clever. ;P
My current favourite phrase: Iv'e seen better!
-SK Genius
You can ask for one potentiometer, check the stamps, and take it from there. Or make new friends at Maplin, and get it done for you. I'm sure they need their software fixed. :laugh: Assuming the object under your care isn't ancient: Are you soldering lead-free? have the tools and materials for it? :)
Luc Pattyn [Forum Guidelines] [Why QA sucks] [My Articles] Nil Volentibus Arduum
Please use <PRE> tags for code snippets, they preserve indentation, and improve readability.
-
You can ask for one potentiometer, check the stamps, and take it from there. Or make new friends at Maplin, and get it done for you. I'm sure they need their software fixed. :laugh: Assuming the object under your care isn't ancient: Are you soldering lead-free? have the tools and materials for it? :)
Luc Pattyn [Forum Guidelines] [Why QA sucks] [My Articles] Nil Volentibus Arduum
Please use <PRE> tags for code snippets, they preserve indentation, and improve readability.
No soldering required, the object in question is a logitech steering wheel I'm not sure how old it is but it's at least 5 years. It has a little connector that's already attached to the board so you can just plug in a new pot (or a new motor if you needed). I do have a soldering iron and solder though. Both quite old though, unknown age.
My current favourite phrase: Iv'e seen better!
-SK Genius
-
No soldering required, the object in question is a logitech steering wheel I'm not sure how old it is but it's at least 5 years. It has a little connector that's already attached to the board so you can just plug in a new pot (or a new motor if you needed). I do have a soldering iron and solder though. Both quite old though, unknown age.
My current favourite phrase: Iv'e seen better!
-SK Genius
SK Genius wrote:
unknown age
aka lead age. the industry has switched to lead-free soldering, different solder, different temperatures. just trying to save the environment (while others pollute the Mexican Gulf and the not-so-blue-anymore Danube). :)
Luc Pattyn [Forum Guidelines] [Why QA sucks] [My Articles] Nil Volentibus Arduum
Please use <PRE> tags for code snippets, they preserve indentation, and improve readability.
-
No soldering required, the object in question is a logitech steering wheel I'm not sure how old it is but it's at least 5 years. It has a little connector that's already attached to the board so you can just plug in a new pot (or a new motor if you needed). I do have a soldering iron and solder though. Both quite old though, unknown age.
My current favourite phrase: Iv'e seen better!
-SK Genius
Be aware that if they are ten years or more old, the solder (and the layer of solder on the iron tip) is likely to be leaded. This does not mix well with more modern (and legal!) lead free, which also generally needs a higher temperature. It may be worth buying a new tip and solder anyway - they aren't that expensive.
Real men don't use instructions. They are only the manufacturers opinion on how to put the thing together.
-
what Griff said, plus this: 1. I doubt it would be a logarithmic one. 2. I would expect a smaller value than 100K, although that is what the stamps suggest. 3. Every software person needs a multimeter; go get one right away! They come in a range of quality, functionality and price. 4. If you have a low-voltage source (say 10V), a 10K resistor and an LED, you can lit it faintly (it would take 10mA to lit properly); if you connect a second 10K in parallel, it should be twice as bright. So try the outer poles of the potentiometer as your second resistor to check it is well above 10Kohm or not. Warning: if you short-circuit the resistor, you'll blow the LED. 5. you could order a few (100K lin, 10K lin, 100K log, 10K log), postage will probably exceed material cost anyway. 6. you could call a friend with more hardware skills and buy him some :beer: :beer: :beer: :beer: :beer: :)
Luc Pattyn [Forum Guidelines] [Why QA sucks] [My Articles] Nil Volentibus Arduum
Please use <PRE> tags for code snippets, they preserve indentation, and improve readability.
-
I live near an actual store so I may as well just go in and buy a few different ones. And maybe a multimeter while I'm there. It's been about 6 years since I needed to use one, it would have made figuring this out easier though. Unfortunately I don't have any hardware typey friends so I suppose I'll do what I usually do with these types of things, which is to stumble blindly through the dark and eventually find a solution (usually by luck) then give myself a pat on the back and a :beer: for being so darned clever. ;P
My current favourite phrase: Iv'e seen better!
-SK Genius
If you have to replace it there's not much reason to test it considering it's probably broken. However if you are confident it's the reason for the problem a much more common scenario is broken solder trace on the circuit board broken connector not making contact.
“If you want to build a ship, don't drum up people together to collect wood and don't assign them tasks and work, but rather teach them to long for the endless immensity of the sea” - Antoine de Saint-Exupery
-
If you have to replace it there's not much reason to test it considering it's probably broken. However if you are confident it's the reason for the problem a much more common scenario is broken solder trace on the circuit board broken connector not making contact.
“If you want to build a ship, don't drum up people together to collect wood and don't assign them tasks and work, but rather teach them to long for the endless immensity of the sea” - Antoine de Saint-Exupery
-
Luc Pattyn wrote:
you could call a friend with more hardware skills and buy him some Beer Beer Beer Beer Beer
Best not to buy them until he has finished the job though!
------------------------------------ I will never again mention that I was the poster of the One Millionth Lounge Post, nor that it was complete drivel. Dalek Dave CCC League Table Link CCC Link[^]
Dalek Dave wrote:
Luc Pattyn wrote: you could call a friend with more hardware skills and buy him some Beer Beer Beer Beer Beer Best not to buy them until he has finished the job though!
Lest he turns a soldering iron into a slaughtering iron.
