Is this a stupid idea? [modified]
-
Tractor + slasher = very dangerous... I have two kids under 8. Therefore me driving tractor through grass with slasher attached = very dangerous for kids. Hence chance of losing a child (under slasher) is as high as the grass (currently about a metre high in the back paddock). It's not funny when you have to explain it... :rolleyes: (Some would say it's not funny period.)
------------------------------------------- Don't walk in front of me, I may not follow; Don't walk behind me, I may not lead; Just bugger off and leave me alone!!
Can't you just keep the kids indoors / away while cutting the grass? Doesn't seem an insurmountable problem...
-
We were given an old 2 stroke lawn mower with a broken pull start. It just so happens that in my socket set is a socket that fits the nut at the end of the crank. I got out the drill, attached the socket and gingerly turned the motor over slowly with the drill. Its got compression so I cleaned the air filter & plug, set the gap & checked the fuel lines.Should I give her a bit with the drill and see if it'll start or is it likely the engine will throw the drill into my face, shin or other body part? The conclution is a bit boring as I managed to repair the starter mechanism
modified on Wednesday, May 21, 2008 8:20 PM
-
That's going a little south of the groin.
Software Zen:
delete this; -
[putting on safety goggles and gloves] No, that sounds fine. :)
Best wishes, Hans
[CodeProject Forum Guidelines] [How To Ask A Question] [My Articles]
Yeah I agree with Hans .. sounds fine. What? Where am I going? Oh nowhere. I just left something behind this big wall. You carry on. :)
The only thing unpredictable about me is just how predictable I'm going to be.
-
You'll need some kind of explosion for the finale, like a Folgers coffee can filled with siphoned gas and some Swisher Sweets. Right on! :-)
- S 50 cups of coffee and you know it's on!
Ah go with Chlorine and Brake Fluid .. makes a bigger bang .. and hey a nice cloud of toxic gas .. lol. As my dad used to say .. if it's worth doing it's worth doing properly :)
The only thing unpredictable about me is just how predictable I'm going to be.
-
ghle wrote:
Stupid idea. Use a rope.
Geez Im stupid. Only thing between me and hospital is CP!
LOL It's too late for that now .. we're on a role :)
The only thing unpredictable about me is just how predictable I'm going to be.
-
We were given an old 2 stroke lawn mower with a broken pull start. It just so happens that in my socket set is a socket that fits the nut at the end of the crank. I got out the drill, attached the socket and gingerly turned the motor over slowly with the drill. Its got compression so I cleaned the air filter & plug, set the gap & checked the fuel lines.Should I give her a bit with the drill and see if it'll start or is it likely the engine will throw the drill into my face, shin or other body part? The conclution is a bit boring as I managed to repair the starter mechanism
modified on Wednesday, May 21, 2008 8:20 PM
Hey Josh, can you give a me run down of your primary skills. Just so I can brush up to fill any potential gap in the market :)
The only thing unpredictable about me is just how predictable I'm going to be.
-
_Damian S_ wrote:
You realise that for about $30 you can usually buy a new pull-cord assembly from your local mower shop, right?
And where's the fun in that eh? The Mrs wants me to take it and have it fixed / serviced but I wanna play around and see if I can get it going. The spring for the recoil of the cord is stuffed and to get to it I have to take off one side of the crank case. I figure if I do that Ill have to make a new gasket, retighten to the correct torque etc. Doesnt seem worth the effort when a new mower from China is only $200
I hear ya. I justified buying a welder so I could repair a crack on the deck of my mower. Burning metal - now that is way cool! I can't understand how the starter recoil spring went under anything that needs a gasket. I've torn apart my share of mowers (and starters), and the starting mechanism is always bolted on externally. Regarding the payoff being $30/hour. If I'm lounging watching the telli, my cost ain't $30/hour. So if do it myself, I save $30/hour, not loose $60/hour. I wouldn't be working anyhow during that time. Good luck. Send pictures. We'll send flowers to cheer you up.
Gary
-
I say film it, and you'll probably win funniest home videos
Christian Graus Please read this if you don't understand the answer I've given you "also I don't think "TranslateOneToTwoBillion OneHundredAndFortySevenMillion FourHundredAndEightyThreeThousand SixHundredAndFortySeven()" is a very good choice for a function name" - SpacixOne ( offering help to someone who really needed it ) ( spaces added for the benefit of people running at < 1280x1024 )
-
We were given an old 2 stroke lawn mower with a broken pull start. It just so happens that in my socket set is a socket that fits the nut at the end of the crank. I got out the drill, attached the socket and gingerly turned the motor over slowly with the drill. Its got compression so I cleaned the air filter & plug, set the gap & checked the fuel lines.Should I give her a bit with the drill and see if it'll start or is it likely the engine will throw the drill into my face, shin or other body part? The conclution is a bit boring as I managed to repair the starter mechanism
modified on Wednesday, May 21, 2008 8:20 PM
-
We were given an old 2 stroke lawn mower with a broken pull start. It just so happens that in my socket set is a socket that fits the nut at the end of the crank. I got out the drill, attached the socket and gingerly turned the motor over slowly with the drill. Its got compression so I cleaned the air filter & plug, set the gap & checked the fuel lines.Should I give her a bit with the drill and see if it'll start or is it likely the engine will throw the drill into my face, shin or other body part? The conclution is a bit boring as I managed to repair the starter mechanism
modified on Wednesday, May 21, 2008 8:20 PM
You've missed the proverbial forest because the even more proverbial trees were in the way. Getting it running implies mowing a lawn.* Why would you want to mow a lawn to begin with? Also - don't be so foolish as to water or fertilize the damn thing. All that will do is encourage growth - which, for those who mow, requires it be done more often. And doing work who's only fruits will yet more work to do is, my friend, quite insane. * Unless you like the sound of a mower, which, although preferrable to Rap and Hip-Hop, is still a taste not easily aquired.
"The difference between genius and stupidity is that genius has its limits." - Albert Einstein
"How do you find out if you're unwanted if everyone you try to ask tells you to go away?" - Balboos HaGadol -
We were given an old 2 stroke lawn mower with a broken pull start. It just so happens that in my socket set is a socket that fits the nut at the end of the crank. I got out the drill, attached the socket and gingerly turned the motor over slowly with the drill. Its got compression so I cleaned the air filter & plug, set the gap & checked the fuel lines.Should I give her a bit with the drill and see if it'll start or is it likely the engine will throw the drill into my face, shin or other body part? The conclution is a bit boring as I managed to repair the starter mechanism
modified on Wednesday, May 21, 2008 8:20 PM
It's an exceedingly *bad* idea. If you're handy enough to clean and gap the plug, then you're handy enough to fix the rope start, it is not a complex mechanism. I recently learned through experience that it is worth the $7 or so to get proper recoil cord instead of substituting whatever you may have on hand; the stuff is readily available from the big box home improvement stores in the U.S. (Lowes, etc.) The engine will probably fire and quite possibly run, if everything is set up properly. That puts you in a position with your hands near the turning blade with potentially as much as ~6hp driving it. It is not a safe idea. Don't try running it without the blade, either. The blade provides the mass the engine uses as a flywheel, and all sorts of unpredictable stuff will happen if the engine starts to run without it. Chances are very good that if the engine has compression and the crankshaft is not bent then you will be able to make a working proposition out of it with minimal expense. Do things safely and correctly and you'll have your health so you can enjoy mowing the lawn! :-) --Geoff
-
We were given an old 2 stroke lawn mower with a broken pull start. It just so happens that in my socket set is a socket that fits the nut at the end of the crank. I got out the drill, attached the socket and gingerly turned the motor over slowly with the drill. Its got compression so I cleaned the air filter & plug, set the gap & checked the fuel lines.Should I give her a bit with the drill and see if it'll start or is it likely the engine will throw the drill into my face, shin or other body part? The conclution is a bit boring as I managed to repair the starter mechanism
modified on Wednesday, May 21, 2008 8:20 PM
We need an engineer, maybe Mr. Wright, to shed some light on the EMF generated by the mower spinning the drill motor fighting it out with the EMF from the grid or battery that used to be the primary driver of the drill motor.
Semicolons: The number one seller of ostomy bags world wide. - dan neely
-
We were given an old 2 stroke lawn mower with a broken pull start. It just so happens that in my socket set is a socket that fits the nut at the end of the crank. I got out the drill, attached the socket and gingerly turned the motor over slowly with the drill. Its got compression so I cleaned the air filter & plug, set the gap & checked the fuel lines.Should I give her a bit with the drill and see if it'll start or is it likely the engine will throw the drill into my face, shin or other body part? The conclution is a bit boring as I managed to repair the starter mechanism
modified on Wednesday, May 21, 2008 8:20 PM
This is a wonderfully stupid idea, and is well worth investigating! If you have any fingers left at the conclusion of the project, let us know how it went. If you have a crisis of confidence, however, replace the recoil starter. Your various bits will thank you, however mutely.
-
You've missed the proverbial forest because the even more proverbial trees were in the way. Getting it running implies mowing a lawn.* Why would you want to mow a lawn to begin with? Also - don't be so foolish as to water or fertilize the damn thing. All that will do is encourage growth - which, for those who mow, requires it be done more often. And doing work who's only fruits will yet more work to do is, my friend, quite insane. * Unless you like the sound of a mower, which, although preferrable to Rap and Hip-Hop, is still a taste not easily aquired.
"The difference between genius and stupidity is that genius has its limits." - Albert Einstein
"How do you find out if you're unwanted if everyone you try to ask tells you to go away?" - Balboos HaGadol -
We were given an old 2 stroke lawn mower with a broken pull start. It just so happens that in my socket set is a socket that fits the nut at the end of the crank. I got out the drill, attached the socket and gingerly turned the motor over slowly with the drill. Its got compression so I cleaned the air filter & plug, set the gap & checked the fuel lines.Should I give her a bit with the drill and see if it'll start or is it likely the engine will throw the drill into my face, shin or other body part? The conclution is a bit boring as I managed to repair the starter mechanism
modified on Wednesday, May 21, 2008 8:20 PM
I would definitely recommend holding the drill with one hand, while having your other hand resting under the mower, between the blades, for no apparent reason (make sure you leave plenty of room for the blades to get up to speed before intersecting with your fingers. Make sure you hold that drill loosely, as well, on the off-chance that it will buck wildly! Bonus points if you can manage to do all this with the drill actually managing to rest somehow between your legs. If you're feeling especially acrobatic, perhaps you should find some way to also get a very up-close and personal view of when the blades actually start moving - I mean, you do want to see exactly how they start moving, right? Definitely drink a case or two of beer before beginning to lower your reaction times, and if you have anything highly flammable at hand, you should be holding some in one (or both) of your hands. Let's see.... did I miss anything? I can't quite think of a way to also get your feet involved; maybe you'll have to do some firewalking first, or something. Just, you know, because. Do you like snakes?
-
I would definitely recommend holding the drill with one hand, while having your other hand resting under the mower, between the blades, for no apparent reason (make sure you leave plenty of room for the blades to get up to speed before intersecting with your fingers. Make sure you hold that drill loosely, as well, on the off-chance that it will buck wildly! Bonus points if you can manage to do all this with the drill actually managing to rest somehow between your legs. If you're feeling especially acrobatic, perhaps you should find some way to also get a very up-close and personal view of when the blades actually start moving - I mean, you do want to see exactly how they start moving, right? Definitely drink a case or two of beer before beginning to lower your reaction times, and if you have anything highly flammable at hand, you should be holding some in one (or both) of your hands. Let's see.... did I miss anything? I can't quite think of a way to also get your feet involved; maybe you'll have to do some firewalking first, or something. Just, you know, because. Do you like snakes?
Trevortni wrote:
I can't quite think of a way to also get your feet involved;
Easy. One hand on the drill, the second playing with the blades. Clearly the feet are involved in lifting it up so that hand #2 can get underneath.
You know, every time I tried to win a bar-bet about being able to count to 1000 using my fingers I always got punched out when I reached 4.... -- El Corazon
-
Trevortni wrote:
I can't quite think of a way to also get your feet involved;
Easy. One hand on the drill, the second playing with the blades. Clearly the feet are involved in lifting it up so that hand #2 can get underneath.
You know, every time I tried to win a bar-bet about being able to count to 1000 using my fingers I always got punched out when I reached 4.... -- El Corazon
-
Christian Graus wrote:
I say film it, and you'll probably win funniest home videos
Which would have been worth it when Toni Perrin was hosting the show ;)
Never watched it with her as host. Bob Sagat was my fav' :D
"Silently laughing at silly people is much more satisfying in the long run than rolling around with them in a dusty street, trying to knock out all their teeth. If nothing else, it's better on the clothes." - Belgarath (David Eddings)
-
NOD32 user wrote:
*The socket was a very snug fit to the drill so it couldn't easily come off regardless
Yeah thats what I was worried about. The socket set is cheap and its only the sprung loaded ball bearing holding the socket into the adapter that goes into the drill chuck.
Duct tape.
